East-coast-supercharging ECS Paxton SC1500 '15 C7 Supercharger Kit Manual do Utilizador

2015 Corvette Supercharger System InstructionsThese instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharg

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 10 nn Reinstall air lter housing along with supplied high-ow air lter, followed by air box inlet and ti

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 11 nn Remove both front wheels, followed by removing the two front lower control arm air deectors held on

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 12 nn Once the sway bar links and tie-rod are free, loosen the sway bar hold-downs held on by two 13mm bol

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 13 njjn Next, prepare for steering rack removal. Start by disconnecting the marked connectors, as pictured

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 14 nn At this point, the rack is ready to be removed. Start by removing two 18mm bolts and then once free,

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 15 nn For ECS balancer installation, remove and discard stock balancer bolt, if using impact gun take care

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 16 nn At this point, reinstall the streering rack, making sure to plug all connectors back in. Be sure to

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 17 nn ABS Block Relocation: To ensure proper clearance of the ABS block it needs to be relocated closer to

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 18 njjjn Radiator Hose Extension: Measure 7 inches from the end of the bend on the driver’s side of the ra

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 19 nSupercharger Head Unit Assemblyn Reinstall fan assembly and attach only the passenger’s side hose clam

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 2 nTools Needed3/8 inch drive ratchet7mm, 8mm, 10mm, 11mm, 13mm, 14mm, 17mm, 18mm, 19mm, 24mm socketsT15, T

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 20 nn Your Paxton SL1500 should arrive properly clocked and ready to install as shown below. Note the refe

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 21 nn Install supplied 8-rib supercharger pulley with the long snout up. Install supplied keyway and retai

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 22 nn With your ECS 2015 C7 Supercharger Kit, a machined and modied water pump manifold must replace the

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 23 nn With supplied .350 spacer, relocate wiring harness on front side of DS head. Next, install bracket a

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 24 nn Next secure tensior pulley with some blue loc-tite. Install bracket assembly 3 on to water pump usin

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 25 nn Slide blower assembly into place making sure all four studs line up evenly. Tighten all four studs w

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 26 nn To adjust the tensioner, place a 1/2 inch drive extension with a ratchet on to adjuster plate. Rotat

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 27 nRadiator Shroud Trimming and Intercooler Installationn Next, the lower radiator shroud will need to be

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 28 nn Take your time when trimming this, as it is critical that your cuts are straight and smooth to help

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 29 nn Using the supplied 6 x 1mm riv-nut and install into the existing radiator cradle hole in between the

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 3 nInstructionsnProperly support car on a lift or properly secured jackstands.nRemove cap from coolant re

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 30 nn Next, it’s time to install the intercooler assembly. Begin by mounting the intercooler mount using t

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 31 nn Next, install the Tial BOV. First place the O rig around the BOV pipe assembly and secure the valve

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 32 nn Using the smaller of the two supplied 3 in. 45-degree elbows, connec the BOV pipe assembly to the su

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 33 nn Install the 3 in. 45-degree aluminum elbow with the short side towards the intercooler and secure wi

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 34 nn Next, prepare the MAF pipe for installation. Install the 3 in. to 3.5 in. reducer on the intercooler

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 35 nn Install the 4 1/2 inch to 4 inch coupler on the factory airbox and the 3 3/4 inch to 4 inch coupler

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 36 nn Sway Bar and Lower Splash Shield Installation: Reinstall sway bar and torque all fasteners to spec.n

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 37 nn Install the modied lower splash shield. Transfer the 10 speed nuts from the OEM splash shield to th

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 38 nn At this point, you will need to modify your stock GM air deector. Measure 1 inch from the tip of th

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 39 njn Next you will need to install the two side air deectors supplied in the kit. Begin by installing t

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 4 nn On the right side of the trunk, you will nd the battery. Disconnect negative terminal.n Remove lower

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 40 nn EVAP System Check Valve: The only modication you need to make to the EVAP system is to add an ECS s

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 41 nn Vacuum Fitting Installation: Find the factory vent hose located on the front of the driver’s side he

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 42 nn PCV System Re-routing: On both valve covers the breather lines are connected to the valve covers wit

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 43 njjjjn On the driver’s side, install the supplied 1/2 inch OEM QC tting and using the supplied 1/2 inc

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 44 nPicture 4Picture 5n All cars: Install the ECS supplied OEM 3/8 inch hose into the factory QC tting on

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 45 nn Reinstall the factory heat extractor shroud with the OEM hardware.n Double check all of your work p

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 5 nn Remove aero scoop held on by four 7mm bolts. n Next, is removal of stock air box assembly. Start by

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 6 nn Next, disconnect MAF sensor by pulling the red tab back on the connector and squeezing the tab to rel

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 7 nn Next, modify MAF housing by measuring 3 1/2 inches from the airbox inlet. Use supplied ziptie to mark

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 8 nn Using a grinding tool or a hand le, smooth down the sides of the airbox inlet to clear the rubber co

EASTCOASTSUPERCHARGING.COM n 609-752-0321n 9 njjn Next, remove air lter housing by removing two 10mm bolts holding it on, as pictured above.n With